Products |
Location of reset button
|
How do I carry out a reset?
|
- LANCOM L54 Serie
- LANCOM L-3xxagn Series
- LANCOM L-4xxagn Series
- LANCOM L-13xxacn Series
- LANCOM 17xx Series
- LANCOM L-822acn
- LANCOM LN-830acn
- LANCOM LN-86x Series
- LANCOM LN-170x Series
- LANCOM WLC-4006(+)
- LANCOM DSL/I-10+
- LANCOM 730VA
- LANCOM 730-4G
- LANCOM 800+
- LANCOM 821+
- LANCOM 831A
- LANCOM 16xx Series
- LANCOM 17xx Series
- LANCOM 18xx Series
- LANCOM 3x50 Series
|
The reset button is located on the
rear panel of the device .
|
- Turn on the device and wait until the boot process is completed.
- Press the reset button for about 5 seconds
until all of the LEDs on the LANCOM router/access point light up.
- Then release the reset button.
|
- LANCOM 1783VA
- LANCOM 1783VA-4G
- LANCOM 1784VA
- LANCOM 1783VAW
- LANCOM 883 VoIP
- LANCOM 884 VoIP
|
The reset button is located on the
front panel of the device (lower right corner).
|
- Turn on the device and wait until the boot process is completed.
- Press the reset button for about 5 seconds
until all of the LEDs on the LANCOM router/access point light up.
- Then release the reset button.
|
- LANCOM 7x11 / 8011 VPN
- LANCOM 7100(+) VPN
- LANCOM 9100(+) VPN
- LANCOM WLC-4025
- LANCOM WLC-4025+
- LANCOM WLC-4100
|
The reset button is located on the
front panel of the device .
|
- Turn on the device and wait until the boot process is completed.
- Press the reset button for about 5 seconds
until all of the LEDs on the LANCOM router light up.
- Then release the reset button.
|
- LANCOM OAP-54-1 Wireless
- LANCOM OAC-54-1 Wireless
- LANCOM OAP-321
- LANCOM OAP-322
|
This device has a serial port,
which is used for resetting.
The device is supplied with a
reset connector , which
plugs into the serial port.
|
- Turn on the device and wait until the boot process is completed.
- With the device switched on, plug the reset connector into the COM/Reset port.
- Wait until all LEDs are off.
- Remove the reset connector from the COM/Reset port.
|
- LANCOM OAP-3G
- LANCOM OAP-321-3G
|
This device has a
blind screw cap marked with
SIM/Reset .
This fitting covers the slot for the SIM card a
small red reset button .
|
- Turn on the device and wait until the boot process is completed.
- Press the reset button for about 5 seconds
until all of the LEDs on the LANCOM access point light up.
- Then release the reset button.
|
- LANCOM OAP-821
- LANCOM OAP-822
|
The reset button is located on the
device panel that accommodates LEDs for the ETH ports
(under a transparent screw cap).
|
- Turn on the device and wait until the boot process is completed.
- Press the reset button for about 5 seconds
until all of the LEDs on the LANCOM access point light up.
- Then release the reset button.
|
- LANCOM OAP-54 Wireless
- LANCOM OAP-310agn Wireless
|
The reset button is located on the
device panel that accommodates the WAN and ETH ports.
|
- Unplug the LAN cable from its connector on the LANCOM. This interrupts the electricity supply over the PoE cable.
- Keep the reset button pressed while plugging in the PoE/LAN cable again.
- The Message LED starts to blink.
- After ca. 5 seconds, the LED stops blinking and you can release the button.
|
|
The reset button is located on the
device panel that accommodates the ETH and SFP ports.
|
- Turn on the device and wait until the boot process is completed.
- Press the reset button and keep it pressed
until the Power LED on the LANCOM lights up again continuously.
- Then release the reset button.
|
- LANCOM IAP-54 Wireless
- LANCOM IAP-321
- LANCOM IAP-322
- LANCOM IAP-321-3G
- LANCOM IAP-3G
|
The reset button is located on the
underside of the device .
|
- Turn on the device and wait until the boot process is completed.
- Press the reset button for about 5 seconds
until the Power LED on the LANCOM light up continuously in red.
- Then release the reset button.
|
- LANCOM GS-1224
- LANCOM GS-1224P
|
The reset/mode button is located on the
front panel of the device .
|
- Turn on the device and wait until the boot process is completed.
- Press the reset button for about 5 seconds
until all of the LEDs on the LANCOM switch light up.
- Then release the reset button.
|
- LANCOM GS-2326(P)
- LANCOM GS-2326(P)+
- LANCOM GS-2352(P)
- LANCOM GS-2310P
- LANCOM GS-1328
- LANCOM GS-2328x
|
The reset/mode button is located on the
front panel of the device .
|
- Turn on the device and wait until the boot process is completed.
- Press the reset button for about 10 seconds
until all of the LEDs on the LANCOM switch light up.
- Then release the reset button.
|
- LANCOM ES-2126
- LANCOM ES-2126+
- LANCOM ES-2126P
- LANCOM ES-2126P+
- LANCOM GS-2124
|
The reset button is located on the
front panel of the device .
|
- Pressing the reset button on these devices does not return the device to its factory settings, it only causes the device to be restarted.
- These devices can only be returned to their factory settings via the configuration interface. See the device manual for instructions.
|
- LANCOM 800 Office
- LANCOM 1000
- LANCOM 1100
- LANCOM 2000
- LANCOM DSL/10
- LANCOM DSL /I-10 Office
- LANCOM DSL /I-1611 Office
|
The reset button is located
behind the front panel of the device .
|
- Turn on the device and wait until the boot process is completed.
- Press the reset button for about 5 seconds
until all of the WAN LEDs on the LANCOM router light up.
- Then release the reset button.
|